Swing Arm Wall Sconce double articulating arm, chrome pivot, cone shade, three finishes.
Two metal arms connect end-to-end at a chrome pivot joint the first arm extends from a round wall backplate, the second arm angles downward from the pivot to the cone shade head. Both arms and the shade can be repositioned by rotating at the pivot joint and the backplate mount, allowing the shade to be placed within a wide arc of positions from the wall pulled close for bedside reading or extended outward for general wall illumination. Available in White, Nickel, or Matte Black.
Articulating range: Both arm segments rotate at their joints, allowing the shade position to be adjusted forward, sideways, and at angle. The arms hold their set position under the lamps own weight once positioned no locking mechanism is required for normal use.
Two arms linked at a chrome pivot the shade can be positioned within a wide arc from the wall.
Polished chrome connector between arms functional accent in all three finish options.
Small conical shade directs E14 light downward focused reading or task illumination.
All three finishes share the same chrome pivot joint. Select at time of order.
Matte white light and clean. Best against white or pale walls where the arm should recede.
Satin nickel cool metallic, coordinates with chrome pivot. Suits contemporary and transitional spaces.
Deep matte black high contrast, industrial, and modern farmhouse. The chrome pivot reads as accent.
Compatible with E14 LED and Edison candle bulbs. A warm-white E14 LED candle at 2700K at 46W is recommended the small conical shade is proportioned for candle-form E14 bulbs and the warm tone suits the reading and bedside positions where this sconce is most often installed. A flame-tip or straight candle-tip LED is the most appropriate shape larger globe shapes may protrude visibly below the shade opening.
Guide to E14 LED bulb selection
| Material | Metal |
| Shade size | Dia10cmH15.5cm / 3.9H6.1 |
| Arm type | Double articulating two arms on pivot joint, adjustable reach and angle |
| Pivot finish | Chrome (all finishes) |
| Finish options | White Nickel Matte Black |
| Bulb base | E14 |
| Light source | LED or Edison candle bulb (not included) |
| Voltage | AC 110240V |
| Control | Standard wall switch (not included) |
| Wiring | Hardwired |
| Mounting | Wall round backplate, hardwired |
| Environment | Indoor only |
| Certification | North America EU AU Saudi Arabia |
The total reach depends on the angle of both arm segments at their respective pivot points. At full extension with both arms roughly parallel to the wall surface, the shade can reach approximately 4050cm forward from the wall. When folded back, the profile is significantly reduced. The installation diagram (see Downloads) shows the range of motion and the mounting centre dimensions. For bedside reading, a position with the shade approximately 3040cm from the wall and angled downward at 3045 provides comfortable task illumination.
Can I install two sconces symmetrically on either side of a bed?Yes this is the most common installation for this sconce. Each backplate mounts independently to the wall at the same height on each side of the headboard. Center each backplate approximately 6070cm from the beds center and at a height of 130150cm from the floor (or 4050cm above the top of the mattress), then adjust the arm angle to position the shade over the pillow area. Both sconces require hardwired installation have your electrician run wire to two in-wall junction points before installation.
Does the arm hold its position or drift over time?The pivot joint holds the arm position under the static weight of the lamp and shade through friction at the joint. In normal use where the arm is set to a position and left the joint will hold its angle. If the joint is repositioned frequently over time, the friction may decrease. The backplate joint at the wall also has a pivot range; this should be confirmed to its preferred angle during installation and tightened securely. If the arm begins to drift, contact us for guidance on adjusting the joint tension.
Is the Swing Arm Wall Sconce certified for North America and Europe?Yes. It holds certifications compatible with North America, Saudi Arabia, Europe, and Australia and operates on AC 110240V worldwide.
